Archive... Timmy F.A.Q.

[ironpanther]

Ok seeing as it seems like half of norcal owns timmies here is the contact information for the two most recommended places to get them fixed. Thank you to magic markers for getting this.

Delta/ BLAST Address and Telephone

Delta Paintball
1820 Arnold Industrial Way Ste D
Concord CA 94520-5325

925-685-7141

BLAST
1799 Carpenter rd.
Oakley, CA, 94561

925-625-7929

blast is where they do the assembly on timmys and also can help. ask for terry. Blast is where your timmy would go for warranty work any ways.

[ironpanther]

PS if you have a Equilizer problem here is the tech email for wicked air sports.

tech@wickedairsportz.com

[paintballer4life06]

How do i make my clamp tighter? I tighten like as most as it will go. Almost popping a nut tightening it. But my egg is still loose even though i havent sanded it. It works fine in my friends Dragon. Is it just a bad clamp or what?

[paintballer4life06]

Im not going to get a answer here am I? lol.

[G5_AlReAdY]

unscrew the piece off and then bend 2 spokes that are straight across from each other that is the only way that i know of to make it tighter and thats wat i did for mine

[paintballer4life06]

ty

[team_mudslide]

the yellow wire connected from the board to the lcd screen was clamped down, then i broke, this is causing problems because something is wrong with my gun ( it is shooting as if the eye was turned off, and i keep choping balls ) and i have no way to see if its turned off (and if it is i cant turn it off)
is there some place in the san jose area that can reattach this wire, or get a new set of wires?

to fix this, i had to buy a new 12 pt lcd/eye harness

thought i would let you guys know if you have this problem

[LiLgBaller916]

Hey Iron Pather whats the website to Blast and Delta kind find them
Thanks

[ironpanther]

I couldn't find it on google so if anybody else knows if either place has one please post it.

[chaosphactor]

Blast/Delta do not have a direct site. ÂÂ*You can call the store direct or go to www.boblong.com and there they have a phone number to the BLAST factory in Oakley.

<Unless you are a factory certified timmy tech like terry please don't advertise how good you are. -Iron>

[RYAN-from-SCHWINN]

www.boblong.com
www.wickedairsports.com

[paintballer4life06]

How much is a 2k2 manual and where can I find one? I herd they might be free ??? ty, bob

[Sinister_Prime]

How much is a 2k2 manual and where can I find one? I herd they might be free ??? ty, bob


Go to the Bob Long website, you can download Owners Manuals on there in PDF format, and yes they are free.

[Sinister_Prime]

OK, now I have a problem that isn't covered in the tech manual........my bolt will chop a ball and then becomes stuck in the forward position, releasing air from the marker. This is not an eye problem, the eyes on my GZ are clean and are functioning properly when this happens. (there is no "delay" when firing like there is when the eyes don't work). I've had my GZ for over a year now, and this just started happening the last 2-3 time I've played. Anyone have any clues? Thanks! ;)

[ironpanther]

check to make sure you don't have any wear around the face edges of your bolt. If you have any kind of space between the bolt and breach then when you chop a ball the shell can lodge between the bolt and breach and hold the bolt and valve open.

[Sinister_Prime]

Thanks Ironpanther, I can always count on you for sound advice. My bolt is a little worn on the top edge, has scratches where the feed tube drops down. There is a small burr inside i guess. I was going to have my body rehoned but I need to completely disassemble it first. Good thing I have a few extra bolts! Thanks!

[kingkeith247]

ok first question...what does forced, simulate, and delayed eye settings do?? and i should run it on forced right?? and second part...with my eyes on forced, every 3/4 times i turn it on...the led says that theres a eye error, is this because theres no paint or what??

[kingkeith247]

another question...does it matter what side the eyes go on?? and if so which sides are they

[ironpanther]

forced is a setting where if the eye doesn't see paint it won't shoot period. Delay pauses the firing sequence for a certain amount of time each shot if the eye doesn't see paint and then shoots no matter what the eye sees. Bypass just ignors the eye completely and runs the firing sequence off of the set timing for however fast you want your gun to max out at rat of fire wise. I don't know about the eye fault but it shoudn't matter what side of the body the eyes are mounted on as long as the transmitter and reciever are plugged into the proper plugs. Transmitter is clear and the reciever is black.

[kingkeith247]

o ok thanks

[Andrew]

today was a horrible day. I kept chopping everything i shot from my timmy until after cleaning it 3 times it stopped shooting all together. The switch activates and it gasses up fione but it wont shoot i can push the bolt for and it makes a popping noise. I cleaned it out completely and dissasembeled it accordong to the manual and re-assembled it the same way. but it still has problems can anyone help?
http://www.sacpaintball.com/albums/album03/Picture_315.sized.jpg when i took that hose off while my gun was gassed nothign happened even when i pulled the trigger

[slugpaint]

Do you have any pressure when pushing the bolt forward? ÂÂ*IF you do try to push the little orange button on the back of the solenoid. ÂÂ*That resets things occasionally. ÂÂ*Try that and then air it up and pull the trigger. ÂÂ*Also is the solenoid clicking when you try to fire it? ÂÂ*Make sure that when you are testing it at home that you did set the eyes on bypass so that it will fire everytime you pull the trigger. ÂÂ*Sometiems I have people that set it on forced then wonder why it won't fire with no paint.

Another thing you should check is your ram bumper.(Yes I see the shocktech ram cap, which might mean you ahve the ram, but some people I know don't use the ram, they only use the cap. Also the loctite that is suppose to go in those might have not been applied corretly, and the adjuster is just backing itself out.) ÂÂ*I'm not sure if you used forced eye mode, but if you do a dead ram bumper will let the bolt go too far back and therefore not tripping the eyes. ÂÂ*Which in turn will not allow you to shoot in forced mode. ÂÂ*Check your ramp bumper, that might be it. ÂÂ*Because chopping paint is sometimes the symptom of a dieing ram bumper. ÂÂ*

Also if you rear hose is off the hose barb, nothing will happen. ÂÂ*Air won't leak when the gun is at rest because there is no air going to that hose. ÂÂ*And when you pull the trigger only a little puff of air will come out of the rear hose

[Big_Papi]

Hey guys I got a timmy with a was 2.7 board. Some how I put it into Competition mode by accident and now I can't adjust the dwell or debounce. I downloaded and read the instructions from the was website but I think they are kinda old. The instructions say that you have to ground the pins on the equalink reciever plug to switch to Competition mode but I haven't touched it. The last thing I did was install the LED but that works with no problems and I don't see how this could cause this problem. I tried disconnecting the LED just to be sure but nothing. I'm at a loss now, any help you guys could provide would be greatly appreciated. :'(

[ironpanther]

try shorting the two pins again to take it out of tourny mode. otherwise you can adjust that stuff through the equalinnk if you have one. lastly if you just can't get it out of tourney mode then you need to contact jim drew through the wicked air sportz board on their site.

[Big_Papi]

Thanks

[Big_Papi]

Got another problem. My gun was leaking out of the the space where you can see the ram when you take the bolt out. Also when I fired my gun it would start burping every couple of shots and the fps was really inconsistant. I figured my cup seal was leaking so I took my timmy apart and sure enough my cup seal had a small scratch on one side. I fliped it around and the other side was good so I put it in that way and my gun stopped leaking. However, my gun is still burping every couple of shots especially when I start walking the trigger. I can't figure out what is wrong. The pressure on all of my gauges seem normal, 275psi inline gen-x2 and 75psi lpr on dualies. I have my dwell at 8 and my debounce at 2. I have also lubed all of my regs and the rest of my gun. I'm out of ideas. Any suggestions?

[ironpanther]

turn your lpr up a bit and check the front and rear orings on your ram. If that doesn't do it then lube you lpr.

[Big_Papi]

Do you know if you can order alias parts from BLAST or Delta? I want to get an alias clamshell. Just wondering if you know.

P.S. The Max Flow is pretty pimp!

Dre

[The_W1se]

Where can you become certified timmy tech?

[ironpanther]

big papi good to hear. call delta I doubt if you can get them from blast. The wise you need to talk to somebody like neil penny or zach long. I think to be "certified" you need to actually work for bob long or for one of his teams.

[paint_punk459]

hey iron, i was just wonderin cuz i live like on carpenter if the place that u are talkin about is a pball store or if u are just refering to bob longs house or somthin cuz he lives on carpenter.

[ironpanther]

umm really I wouldn't know. That is just the information given for mailing adress for BLAST. For all i know he could assemble his guns in his garage. I have not actually been there.

[paint_punk459]

o thanx neways. i think it is bobs house, he has a pretty sick xball field in his back yard, but its all deflated. u can see a video of it on smacktalkpaintball.com and in the background u can see the football field lights of my high school ;D

[FatalIgnorance]

u just have to take their "class" to become certified. they hold em at big events sometimes, they had one at huntington beach i went to. pretty much a q/a thing but hey im certified now

[norcalkiller]

hey i have a 2k2 timmy and the other day i was dry firing it and noticed that the ram sleeve was pushing out of the back of the gun about half of a centimeter. at first the ram cap was unscrewed a lil bit from the gun shaking while dry firing it so i screwed it in after de-airing it and then i noticed the ram sleeve was pushing out so i pushed it in and aired it up again and it popped out again the same distance. a couple people at the field i was playing at sed it was a factory problem but i dont kno. if you have ever seen this problem before or kno someone hoo has please reply to htis post with anykind of help cuz i got a tourney in 2 weeks and i have practice at scp for the tourney in like 6 days so i really need to get my gun fixed but i dont want to drive hella far down to delta so if you kno if this is something that my local kapp tech can fix without ripping me off or if this is a big problem that i would need to take down to delta please tell me. thanks.

[North_Cal_Baller03]

hey oakland i posted in your thread

[brown_terror]

my girl got me an alias timothy for fathers day,68 4500crossfire. with factory settings eye on force, 10 bps. is this right? if so how do i make it faster without bounce?

[brown_terror]

and holo b

[ironpanther]

if you have a halo B on there and it is on forced you are just fine for having it shoot fast. if you want to keep it from bouncing at all but want a nice crisp light trigger just turn up your debounce and mbounce a little.

[brown_terror]

i was given an alias for fathers day :o , out of the box it shoots 11 bps. i had adjusted the trigger as tight as possible w some slop. 11 bps w/paint 16 cycles per sec w/no paint. by the way its my first timmy

[brown_terror]

nevermind the last post i thought the one before that didnt post thanks panther, sheesh you guys must be busy cus i posted on the cocker thread (bad eye), and you and psy. are pretty timely with knowledgeable response. BIGG UPS TO BOTH. later thanks

[UberMunkey]

raise teh dwel some

[ironpanther]

make sure your bolt is not flipped. ::)

[PBALLIN]

umm really I wouldn't know. ÂÂ*That is just the information given for mailing adress for BLAST. ÂÂ*For all i know he could assemble his guns in his garage. ÂÂ*I have not actually been there.


just fyi the factory is on the same property as bobs house
-mike

[ironpanther]

thanks mike. And I wasn't suggesting your that silly I was just mearly pointing out one possibility. I have seen it more than once.

[PBALLIN]

also clean and relube ur LPR and check to make sure u dont have something stuck in out of ur hoses
-mike

[shotout]

hey i got a new timmah and i need to lube it i heard of a lube called dow 55 without lithium crystals and i need to now if this stuff works,where i could buy it, and if it would cause my drop off problem to go away and by the way iron panther you are doing a great job helping out all of these peeps appreciate it

[Dakkon]

yardbirds, homedepot, wherever. Yea dow 55 is good.

[ironpanther]

the only two lubes you use on a timmy are dow 55 for the ram, and reg pistons, and triflow for the bolt Orings. If you can't get ahold of dow 55 you can use dow 33 but it won't last as long because it is of a lower viscosity.

[NORCALBALLIN]

to answer somebody question earilier, you can not buy alais clamshells from anywhere as of now! thats why alias's are so much right now! they run for about 400$ on pbnation....

Peace, Dean
Team Loki

[JT_man]

hey I have a 2k2 with w.a.s. 2.7 and my eyes dont work but whats wierd is that they dont read but they dont go into bypass for some reason can some one help me ???

[JT_man]

never mind i fixed it ;D

[tesnve]

Well my gun is leaking out of the solenoid but its still shoots fine but only up to 225 fps
Should i take it apart and lube it?

[Dakkon]

yes

[MATTY]

i just got an a-bomb timmy a few weeks ago and everytime i go out to play i chop every couple shots to where i don't even play the rest of the day. i have messed with the dwell,lpr,bip,bolt and put different detents in just bout everything and it still chops does anyone know why it is doing this, or the settings bip, etc. should be set at?

thanks

[ironpanther]

dwell 8-11
bip .12-.15 (I can't be sure on that)
make sure the battery is good and the eyes are on forced mode.

[SicJester101]

Micro switch problem!!

K I was messing with my gun trying to get it faster. durring this i messed up the conncection between the micro switch and the wires running back to the board.
Its under that little rubber connector...i can push them together and it works. my problem is: how do i get it to stick and stay connected under the rubber connector ??

any help would be great right about ....now thanks- ryan

[ironpanther]

the rubber "connector" is not a connector but a little piece of heat shrink tubing. If you take the tubing off, cut a new length of tubeing that you slide down the wire a little ways then resolder the wire connection you can slide the tubing back over the solder point and shrink it down using the soldering iron or a heat gun and you will be back in business.

[shop11phoenix]

dwell 8-11
bip .12-.15 (I can't be sure on that)
make sure the battery is good and the eyes are on forced mode.


FYI. Bob Long suggest that you run your eyes on Delay. I would suggest that also. Running them on forced kind of defeats the purpose of the eye.

[ironpanther]

aaron I don't know where you got that from but running your eyes on forced employs the full use of the eyes as the antichop mechanism that they are. Yess I agree delay is good most the time but if you shoot anything but a halo then forced is much better.

[FatalIgnorance]

i would like to hear how u justify that panther? putting the eyes on delay IS better because it makes it 10x easier to solve an eye/hopper problem. if the gun shoots however much time after u pull the trigger, then u know ur eyes are working and the hopper is not. if it shoots paint but not right when you pull the trigger, it is an eye problem. what do you do in forced mode if the gun doesnt shoot, is it an eye problem, or is it a hopper problem? also bob long did say delayed is better during the timmy tech class.

[shop11phoenix]

aaron I don't know where you got that from but running your eyes on forced employs the full use of the eyes as the antichop mechanism that they are. Yess I agree delay is good most the time but if you shoot anything but a halo then forced is much better.


Ironpanther: At the Huntington Beach NPPL Super 7 there was an Intimidator Tech class where Terry Fong, Little John, Bob Long, and one other tech spoke about the way the intmidator functions and the best way to troubleshoot them. That's where I was told by Bob Long that he suggests to run his guns on delay rather than forced... He also said a lot of people assume that forced is a better way to go then delay, but delay gives you the advantage on the field to see if you're having a hopper problem or if your eyes are working properly.

[shop11phoenix]

i would like to hear how u justify that panther? putting the eyes on delay IS better because it makes it 10x easier to solve an eye/hopper problem. if the gun shoots however much time after u pull the trigger, then u know ur eyes are working and the hopper is not. if it shoots paint but not right when you pull the trigger, it is an eye problem. what do you do in forced mode if the gun doesnt shoot, is it an eye problem, or is it a hopper problem? also bob long did say delayed is better during the timmy tech class.


Read my mind Rob.

[ironpanther]

aaron and rob I will say this in favor of your arguments. delay mode is a prefferable mode for diagnosing problems that may arise do to faults with the eyes. I still stand behind my original statement in that the better mode to operate the gun normally is forced because, and here is the caviat, as long as the gun is properly teched in the first place, there should be no eye problems from the time you check that your gun is operating properly before you walk onto the field to the time you walk off the field. This is why in xball players have more then one setup that they are used to using and also why teams practice and pro teams have techs. so that the player does not have to use a mode that risks a chop on field when it counts the most. I have teched and played with enough timmies to know the benefit of delay mode when working on them but I will not personally, nor allow a team mate to, walk onto a field for a tourney using anything but forced on their guns.

[FatalIgnorance]

so ur going with the idea that ur gonna chop if you have it on delay because a ball will only be half fed. too bad the chances of that happening arent very likely. and of course pro teams have their own techs etc. etc. but i think ill take bob longs word over yours.

[ironpanther]

hey when it counts why risk it. I have seen things happen on a paintball field more than once that the odds are near impossible of it even happening in the first place. All I am saying is the better prepared you are(porperly teched guns) the less you have to risk. If you aren't picky enough to eliminate some simple risk like a ball being half loaded when the delay time runs out then you obviously don't have enough of a desire to win. Only by eliminating or reducing to the bare minimum every risk you can will you be able to play your best. but feel free to take bob's word he invented the gun. I will never have that credential no matter how many I use and tech.

[SicJester101]

K ive got another problem with my 2k2 timmy. :-\

im using a halo in force mode (the halo is feeding for sure) but fro some reason the gun is being wierd like shooting and then all of a sudden stop shooting but if i like slightly move the bolt forward or tap the gun on the side it shoots again .... :-\ i cant figure it out

any help would be GreaT

[Dakkon]

ram to far back?

maybe (only seen this once on my friends 2k2)
balls getting stuck in feedneck?

[ironpanther]

yeah ram needs to be adjusted forward. common problem.

[FreeAgent916]

hi,
when i dry fire or force fire the bolt pin pops up and the bolt doesnt go what do i do?

pm me for the answer thanks

[alias_killa]

well you dont have your bolt in right

[Dakkon]

It could also be that his bolt pin isn't in tight enough (for bolt to be upside down he would of had to take pin out anyways), just tighten it through the allen screw on the back.

[FreeAgent916]

thanks....the light on my gun beeps yellow, then when i fire green and also red what does that mean

pm me wit the answer or just answer on this forum

[FreeAgent916]

how do u change the battery

[ironpanther]

if the light is flashing yellow after you have turned it on and haven't pulled the trigger yet you need to change the battery. You chaneg the battery by taking the grips off and then unscrewing the screws that hold the side panel of the clamshell and taking the panel off. at that point you will be able to remove the battery and swap it for a new one then put everything back together.

[pballer1018]

hey what is debounce one actually doing because my friend tells me it firing twice everytime i pull the trigger but im pretty sure hes wrong.
lmk

[ironpanther]

ok here is the technical explanation. debounce is an electronic digital filter that decides what is and is not a trigger pull. this is accomplished by saying ok on debounce three the switch has to register one and a half milliseconds of a closed switch or three or what ever the timing is. The lower the debounce the less time the board requires the switch to be closed before it registers it as a trigger pull. But in the switches of today they are not just on and off. as the trigger comes closer to being closed small amounts of charge bridge the air gap and look like trigger event. IF the debounce is set to one the sensitivity to those events is though the roof so many times when a switch is being depressed it will register those first little charges as a separate event and thus trigger pull. This makes it so the board can register mutiple trigger events per physical pull and result in electronic bounce. Debounce as stated above filters out these false trigger pulls by requiring a certain amount of sustained events(closed circuit in the switch) before it recognizes it as a pull.

[ironpanther]

you have a leaking reg seat in your LPR. If you have a seals kit find the tiny plastic ring that is square on all sides and semi clear. Its a little bit smaller than a quarter inch in diameter. Take your LPR off your gun when the gun does not have air. If you have the 2k2 or dual style lpr then unscrew the cap off the lpr. If you have the lasoya, ironmen, or dragon style unscrew the LPR housing from the part that screws into the front block. This can be done with a strap wrench and a crescent wrench if the housing is screwed on tight. This last step does not require taking out the adjuster screw so in the whole project no allen wrenches are required. Now you should be able to remove the spacer, spring, and piston and see the reg valve pin. Now you need a deep socket wrench or driver(I believe the size will be 3/8ths to remove the valve assembly. I emphasize deep because if you bend the reg pin(which is very easy to do) it is hard to get it straightened out and then you will have to buy a new one. Carefully unscrew the valve assembly and remove. You should see a spring, stem, seat, oring, and threaded piece that all come out nicely. Now replace the seat(the part around the stem that seals with the threaded piece). Be very carefull when screwing the valve assembly back into the gun to only tighten it to finger tight. The threads are very easy to strip and the seal is made with that little black oring you saw so it doesn't have to be super tight. After thats in clean and regrease your piston Oring and insert back in. Reinsert the large spring, place the spacer on the spring and screw on the LPR housing or cap.

If you did all this correctly and didn't touch the adjuster screw on the lpr you should find that the creep in the reg is fixed and the pressure setting of the lpr is the same or very near the same.

IF you don't trust yourself to do all this find a local timmy tech and tell him you have a bad reg seat in your LPR thats causing it to creep and you need a new one installed.

[ironpanther]

that may have been the case. one thing you can do to regularly make sure the reg seats are ok both in the LPR and the torpedo is this.

LPR
Make sure you don't take your LPR off your gun for this.
Take the cap off as described above and remove the spacer, spring, and piston.
air up the gun.
If you notice a tiny hissing noise then the reg seat should be changed. You can tap the valve pin a few times with the handle of a slim screw driver to see if that doesn't seal it but if the leak persists see above for changing.

Torpedo
Same deal. Leave it on the gun, take the lower half off and remove the spring, spacer, and piston. air it up. if it hisses then the seat is bad and replacement is exactly the same as the LPR.

[P8ntballIn08Olympi]

i have a 2k2 timmy w/ a frenzy 113 and stock trigger

my sets r
Dwell 8.5
eye force
bip o.o8ms
bolt 15 ms
db 2
mb 00

i have heard ppl talkin about turning mb and db up and getting no bounce :-\ i was wonderin how i wuld do that and wut it wuld change

[P8ntballIn08Olympi]

another prob mym mb will on gfo up to 2.00 is there a way i can make it go higher

[ironpanther]

this would be where I say. Read the fing manual. If you don't have one look it up online all of this is covered in the manual.

[P8ntballIn08Olympi]

panther ur a life saver i got a sweet trigger job thx 2 u now my bps is 3-5 balls faster and i fixed my sets they r

Dwell 8.00
Eye Force
Bip 0.01mS
Bolt 12mS
Db 2.00
mb 2.00

again thx panther

[alias_killa]

timmy lover turn your BIP to 5 or the lowest it goes that will make your gun even faster

[P8ntballIn08Olympi]

i'll try it :)

[P8ntballIn08Olympi]

.5 or 5.o

[P8ntballIn08Olympi]

on the bottom of my torpedo reg i have a little screw and i have been lookin at pics on boblong.com and onthis forum and i see that everyone has theirs screwed in all the way but when i screw mine in it leakes from that screw

plz help me

[Pvilleplayer]

im lookin into a timmy, commin from a impulse, im still in the early stages, but im lookin ahead, will i have to get a LP tank? i already have a HP tank?

[I-want-an-angel]

i would get a lp tank because in the manual for timmys it sats that a lp tank should be used i have a lp tank on mine and it works great!!!

[Pvilleplayer]

thanks, one more, what is the frame that the alias comes with called? thanks in advance.

[ironpanther]

the alias grip frame? just a thought.

[lewdogg21]

Last night I took apart my 2k3 lasoya and was messing with my trigger settings. I was using a small allen wrench to lightly press on the trigger switch to test how short I could make my trigger pull. Unfortunately now my trigger switch doesn't seem to be working. My solenoid isn't making the clicking sound and my shot counter is not advancing at all. I air'd up the gun and put it all back together and still not firing. Do I need a new switch? It worked fine untill i touched it. Can you short it out?

My alias had a similar problem where it wouldn't fire every trigger pull so I took apart my working gun to check out what a working one is like and now both are screwed up. I see that I can buy a WAS Switch for $10 for the lasoya but what about my 2k4 alias? Is that something that I would need to call delta/blast about?

[ironpanther]

first off simply check to make sure your not in like forced or delayed because that could be that smack your forehead feel like an idiot problem right there. Next if that doesn't work is make sure the switch still clicks. if the swtich clicks back and forth then it is still good and you need to make sure all your wiring is good. I have found that WAS boards are pretty hard to screw up so just pressing a switch with an allen wrench should mess it up. Lastly if all else fails call blast or WAS and see what they have to say.

[lewdogg21]

Iron and all those who read this,

I stopped by home for lunch on the way to a meeting and yes that was the root of my problem. After realizing how stupid it was I thought of those who would post attempting to help me and I felt sorry for them.

gg me.... ::)

[ironpanther]

lew don't worry about it we all have those kinds of days. Way back when on here there was a question about a model 98 that was breaking every ball and the guy couldn't figure out why. everybody took a crack at suggesting a solution and nobody thought to ask if the ball latch was in backwards. Seriously i have seen these kinds of simple mistakes and not been able to see them for what they are so don't worry about it. just think next time. What is he simplest reason for the gun not working how I want it too and work up from there.

[I-want-an-angel]

where can i get a new on off switch for my lasoya it got wet and stopped working and i really need a new one


and how much will it cost?

[Et3rnal]

Hey, I just recently got my alias about a month ago. My bottom reg adjustment screw became cross threaded and is at a sideways angle, completely ruined. Is there any warranty that covers this and if so where do i send it to get it fixed? thank you.

[Dakkon]

I don't believe you crossthreading a screw is warranty covered. But who knows, you can also buy a new bottom if you have to.

http://www.bradyspaintball.com/boblore.html

[ptr]

i just got an alias, it has a 110 frenzy in it.i was wondering if there was somewhere i could send it in to get it updated? and also what r good settings cause i didnt get a manuel and i know nothing.

[Dakkon]

send it to blast to get updated to 127.2 for 40$.

For settings trying something like this..

BIP: 5ish
Bolt: 10-15
Dbounce/mbounce: Whatever you want (did 110 even have mbounce?)
dwell: usually around 8-9.5
eyes: forced

[Et3rnal]

Ty for the help Drakkon. Just wish it was covered by the warranty because it was not my fault at all that it cross-threaded... 60$ for a new reg...

[ptr]

there is no mbounce and thanks for the info it shoots great but on delay with a empire halo.

[Dakkon]

call blast and ask them about the crossthreaded screw, they might cover it. I know for say stripped holes they said it would cost 40$. On the older models. If its newer they might cover crossthreading.

925 625-7929

[BRANDON13]

what threads is the 2k2 feedneck. someone told me they were autococker but what kind. there are 2 the autococker threads and the sto autococker threads. are the alias threads the same as the 2k2 threads? cause ive heard that they were. im a little confused. Can someone please help me.

[ptr]

what threads is the 2k2 feedneck. someone told me they were autococker but what kind. there are 2 the autococker threads and the sto autococker threads. are the alias threads the same as the 2k2 threads? cause ive heard that they were. im a little confused. Can someone please help me.


????, that is a good question, cause you can get 2k2 feednecks for $$cheap$$

[BRANDON13]

what threads is the 2k2 feedneck. someone told me they were autococker but what kind. there are 2 the autococker threads and the sto autococker threads. are the alias threads the same as the 2k2 threads? cause ive heard that they were. im a little confused. Can someone please help me.


anyone and how can i tell if the 2k2 feedneck can come off or if its press fitted. reason i asked is cause the person at the pb store said he cant take it off cuase its press fitted but i remember seeing the feedenck turn but it just stopped and i can see marks on the neck that look like it has been turned before.

[ptr]

the feed necks should come off.

[Big_Papi]

2k2 feednecks are press fitted. If it is a clamping feedneck the top should screw off, not just the adjuster part.

Dre

[TEAM INSANITY]

hey i have a z timmy and the eyes arent working for some reason like i checked all wires and everthing and the eyes arent fried i take good care of them and i jsut got it.. and i have ot shoot my gun in dry fir mode also someone please help me out thnaks ahead

--------------julius------

----------------isnanity----------

[OakLand HellRaiser]

anyone know what the threads are for the barbs on the sleeve? They are a lil smaller than cocker i think.

Can i have it in the actaully measure of the threads.

[Got_Paint]

Also make sure you aren't pinching any wires.

[CallMeLucky]

i went to Sinister Paintball a while ago, and my microswitch was broken, they dissassembled my gun, and i was wondering where to send it if i need a new board and new wires...no offense Sinister but they did kind of a sloppy job, they did a good job assembeling it, but it broke a couple wires, nothin 20 bux can fix

[PsybusterX]

take it to blast, but if you want to do it yourself you can stop by radio shack and pick up a lever microswitch and all you need to do is pick up some electronic wiring and solder the 2 wires to the board (if you feel comfortable about soldering)

[drunkballer77]

the solenoid on my alias leaks. air comes out through the holes in the front. the holes that are above n below the hose in the front part of the solenoid. i would cover those holes with two fingers n then it would gas up. how do i stop my solenoid from leaking? also i cant get my fps to go past 250. any thoughts???

[OakLand HellRaiser]

the solenoid on my alias leaks. air comes out through the holes in the front. the holes that are above n below the hose in the front part of the solenoid. i would cover those holes with two fingers n then it would gas up. how do i stop my solenoid from leaking? also i cant get my fps to go past 250. any thoughts???



pretty simple problem, u hope. Most likly u need to lube and clean ur noid. The lil vavle inside can start sticking, and it will let air out one of the unused holes. Just unscrew it and MAKE SURE U REMEMBER WHERE EVERYTHING WENT AND WHERE U PUT IT. we are taking a gasket that is very small, along w/ a oring that is prolly the smallest u ever seen, along with lil metal shafts that u will lose if u aint careful.

Before u try this, i would hit the red button on the noid, this is basicly a manuel activation, but try it to see if it has to do w/ wiring or board.

[OakLand HellRaiser]

I just got a new frenzy 127 and i hav an ECX led and i was wondering i u new a site that had an LED manual.LMK


If im right u cant setup a frenzy w/ led? Or is that the enotry(sp)

[Big Joe]

the solenoid on my alias leaks. air comes out through the holes in the front. the holes that are above n below the hose in the front part of the solenoid. i would cover those holes with two fingers n then it would gas up. how do i stop my solenoid from leaking? also i cant get my fps to go past 250. any thoughts???


Instead of doing what Cali Guy suggests, send the solenoid into BLAST and they will replace it. As for your FPS, it could be a number of things. Incorrect pressures, bad poppet, or something within your inline. Send the gun into BLAST with a note or take it to Delta and have Zach look at it.

Hope this helps.

Joe

[Big Joe]

I just got a new frenzy 127 and i hav an ECX led and i was wondering i u new a site that had an LED manual.LMK


Go into PBnation to the Bob Long forums and do a search for the manual. Terry has posted alot of information on the board. You can also call BLAST and they will send you a sheet of paper explaining the board.

You cannot program the board through trigger pulls like a WAS board. You will have to invest in a new 12pt harness, membrane switch, and LCD screen in order to change settings.

Hope this helps.

Joe

[OakLand HellRaiser]

so u need lcd and i right? Anyway..........is that a 2k4 board or a 2k2? Basicly is it lcd or like a 113?

[Big Joe]

His ECX that he has would have a 2K2 style Frenzy board and the latest software for that style is the 113, unless you upgrade to the 127.4.

[drunkballer77]

right on cali guy & big joe.... thanks for the help

[OakLand HellRaiser]

sending to blast or fixing?

[Big Joe]

right on cali guy & big joe.... thanks for the help


No problem.

[CallMeLucky]

if you dont want your 127, ill buy off you for like 60 bux, and then you only need about 120 more to get a infamous board, which is perfect for your gatizzle

[Dakkon]

pretty simple problem, u hope. Most likly u need to lube and clean ur noid. The lil vavle inside can start sticking, and it will let air out one of the unused holes. Just unscrew it and MAKE SURE U REMEMBER WHERE EVERYTHING WENT AND WHERE U PUT IT. we are taking a gasket that is very small, along w/ a oring that is prolly the smallest u ever seen, along with lil metal shafts that u will lose if u aint careful.

Before u try this, i would hit the red button on the noid, this is basicly a manuel activation, but try it to see if it has to do w/ wiring or board.


Only remove the TOP of the solenoid, don't remove the bottom, the bottom has the 2 metal shafts which can easily be lost and theres no reason to open. Just open the top, don't lose anything, pull the thing out, and clean it, lightly grease it.

[Sflyingcow]

my classic timmy leaks out of the retaining allen on the bottom of the boddy right inbetween the middle barb and the frame screw hole

[Dakkon]

Are you sure its there and not somewhere else? If it's there for sure, it's the ram sleeve orings.

[superduper77]

hey i got a problem with my ecx with a s.o.b. 2.0 it bounces like crazy i went to my first tournament and they didnt allow the gun so i was stuck with a rentle which sucked but does anyone know how to fix the bounch on the gun?

[superduper77]

but its wierd if it doesnt how come i couldnt use it in the tournament the ref check it out finger walked it and he stop it just kept goin for like another 5 balls

[Sflyingcow]

yeah its definaltey the retaining allen i thought it was those o-rings but i can;t get the barbs off any tips?


superduper77 -adjust the trigger setting hex screws just play with them and see if u can get it to stop bouncing

[X cretean baller X]

i have a 2k2 with frenzy 113, when i put my eyes on forced or delayed and have no air no paint and nothing in the breech my gun will still fire. i have checked to see if my eye covers were tight, i cleaned my eyes i checked to see if they were plugged in correctly to the board but when i put a flash light over my geed neck so i could look throught the front of the gun to see if it was clean it would not fire on forced and it would delay one sec on delayed but when i took the flash light away it went back to normal and would fire on forced and would NOT delay one sec on delayed


someone plz help i would hat to have to drive all the way to predator or adrenelin zone

[Dakkon]

Clean the eyes with a small amount of alcohol. ALso check for any pinches in the wires.

[Dakkon]

wocgniylf#1 - Try pliers, or the correct size socket thing.

[fuzzyrabbit]

my lasoya is shooting 2 to 4 balls each trigger pull
it has a WAS 2.7
and when i walk the trigger it chops balls
I NEED HELP!!

[BONKERS]

hey my GZ is leaking out of my ram and i've tried everything i know i v've relubed my whole gun my soleniod isnt leaking so its not blown i just cant figure it ou it was working fine the day before

[OakLand HellRaiser]

Fuzzyrabit-----

Try turning ur db to like 10, if it is still doin that, check ur trigger and switch. If none of that works send the gun to bob, if it isnt db probs then its a faulty board.


Bonkers-

thats a easy fix. Its the orings on ur ram. U can get some at homedepot or i would buy a repare kit, cause u prolly want to replace ur cupseal also.

that should solve it

[recon1990]

is there a website like the matrixcenter but for timmy

like a website just fot timmy part and upgrades?

thanks

[cereal killer]

suction noise everytime the trigger is pulled does anyone has any ideals what it could be ,i lube all the o rings,also drop balls

[clud1324]

hey i got a 2k1 classic and whenever i screw my tank into it the air shoots out of my air valve thing in the grip. is it brken and do i need a new one or wut?

[Dakkon]

suction noise everytime the trigger is pulled does anyone has any ideals what it could be ,i lube all the o rings,also drop balls



Did you grease the regs? Could be a recharge sound. Also make sure the bolt slides easily while de-aired.

[Dakkon]

hey i got a 2k1 classic and whenever i screw my tank into it the air shoots out of my air valve thing in the grip. is it brken and do i need a new one or wut?


I'm guessing you are talking about your solenoid, is it leaking out out of the side, or out of one of the hoses/barbs. Try to be more specific.

[clud1324]

itz leaking out of the side holes not the tube

[cereal killer]

suction noise everytime the trigger is pulled does anyone has any ideals what it could be ,i lube all the o rings,also drop balls



Did you grease the regs? Could be a recharge sound. Also make sure the bolt slides easily while de-aired.
yes i grease the regs,recharge sound maybe but my alias doesn't make that noise when it recharge

[cereal killer]

problem found reg was no good change reg

[ironpanther]

Turn your LPR down. If your solenoid is leaking then you have over pressureized it and probably need to replace it.



itz leaking out of the side holes not the tube

[RevoltingBlob]

i have a tx storm timmy with was board and have no idea about the settings like dwell,debounce,eye mode,bip delay,ram delay,bolt delay. so if u have settings or know where i can find some good ones let me know.

[CallMeLucky]

i recently bought a infamous timmy, but i cant open it until christmas so i was wonderin does the infamous take timmy parts or defiant parts like

bolts, ram caps, lprs, and such, and also trigger guards and triggers

[OakLand HellRaiser]

i have a tx storm timmy with was board and have no idea about the settings like dwell,debounce,eye mode,bip delay,ram delay,bolt delay. so if u have settings or know where i can find some good ones let me know.


http://www.sacpaintball.com/forums/index.php?board=14;action=display;threadid=9044

started by one and only

[RevoltingBlob]

thanks cali guy

[contractkilla02]

hey idk what happened, i was shooting my paint out when we were leaving, and i chopped a ball in the bolt, it started leaking out, so i had to turn my airsource off, then i got the bolt back and cleaned out the ball from in the chamber pretty good, now my bolt pin wont click up, which means i can clean my bolt, is there something wrong with the ram, or the eyes? idk help!!

[Davvid]

i recently bought a infamous timmy, but i cant open it until christmas so i was wonderin does the infamous take timmy parts or defiant parts like

bolts, ram caps, lprs, and such, and also trigger guards and triggers


First the Infamous is a Timmy, it's just the new 06 stile.
Yes Zack Long told me the new 06 Guns such as the Infamous are a new design.
When you buy anything for them you must make sure you specify it's an 2006. Allthough the new Infamous board will fit our 05's. I just put one in my Alias and I just 05's my ****ies and put an Infamous board in it. the only thing Terry showed me you have to cut about 1/3 of the metal tong of the microe switch, just enough to clear the metal block in the handle were it goes.
But yes to answer the question, you have to make sure the parts are for the 06 Timmies.

[Davvid]

hey idk what happened, i was shooting my paint out when we were leaving, and i chopped a ball in the bolt, it started leaking out, so i had to turn my airsource off, then i got the bolt back and cleaned out the ball from in the chamber pretty good, now my bolt pin wont click up, which means i can clean my bolt, is there something wrong with the ram, or the eyes? idk help!!

Sorry I didn't see this sooner bro. Don't muscle anything yet. first look in the back of the gun at your bolt. you'll see a set screw that uses a alan wrench. turn it to the left (unscrew) just a 1/4 turn first. this set screw pushes on a spring that pushes on a ball bearing that sets in the holes of the bolt pin. If it's to tight you won't be able to pull the pine. Just try losening it just a hair first then if it's still tight a little more.
(and opposite if anyone is haveing a hard time keeping the pin in place if it pops up while in play just tighten the set screw.
Hope this helps.

[contractkilla02]

what is the best settings for a 127.4 LCD?

[mxrider6190]

go to the nation dylan and look for thomas settings they were pretty fast for me his name is liek smartpartskid and his avvy is a karnage

[contractkilla02]

alright thanks

[lost_cause]

i just got a 127.4 board for my texas storm and i was wondering wat settings i should use. the "stock" settings on it were all over the place

Dwell---11.0
eye mode---force
BIP---0.2ms
bolt delay---13ms
delay---00
Cap---off
Debounce---15.0
M bounce---00
Comp mode---semi

Can someone please help me out!

[contractkilla02]

i just got a 127.4 board for my texas storm and i was wondering wat settings i should use. the "stock" settings on it were all over the place

Dwell---11.0
eye mode---force
BIP---0.2ms
bolt delay---13ms
delay---00
Cap---off
Debounce---15.0
M bounce---00
Comp mode---semi

Can someone please help me out!


put ur dwell at 8.0
and bolt delay at 12ms