Nomad627
09-06-2004, 06:19 PM
Ok,
I'm at my wits end. I picked up a 2k2 in almost new cond.
Looks like it was barely if ever used. Shot well when tested.
Early 1.4.3. board, rounded edge clamshell.
When i first got it, i tore it apart and cleaned and lubed both
regs. They were really clean. installed a 300psi gauge for the hpr and backed out the allens on both reg flush to start off.
Went in my backyard to test fire and chrono. Gassed it up and brought the hpr to 250 and the lp to 75. shot over the chron at about 200fps. the dwell was at 8 and it's the early black wired solenoid. Kept raising the hpr to till i got to 300 and the lpr till i got to 100. top speed was 260fps.
I kept changing the dwell higher and higher, but it didn't make a difference. I guessed it was maybe the board. I got one from a friend , a 2.0 that is known to be good and the same results. I had a chance to buy a frenzy board and i was going to replace it anyways, but still no higher velocity.
The battery was good, but i changed that too.
I tore apart and lubed the LPR and HPR and thier pin valves still nothing.
I called Blast and the tech there didn't know what was wrong and said they were backed up and if i sent the gun in it would be 4 weeks before i got it back.
So i tear into it again, took off all the hoses going to the solenoid and make sure there not leaking and all the barbs to be sure they were not blocked. I had 2 spare hi flo barbs and put them on the output of the solenoid and test it again . Now i can get it up to 270fps once in awhile, but a consistent 265fps. I brought the dwell from 8 to 10 to 12 to14 and maxed out to 16 and still the same velocity.
What else is there?
Whatever light you can shine onto this problem would be gladly appreciated
Nomad627
I'm at my wits end. I picked up a 2k2 in almost new cond.
Looks like it was barely if ever used. Shot well when tested.
Early 1.4.3. board, rounded edge clamshell.
When i first got it, i tore it apart and cleaned and lubed both
regs. They were really clean. installed a 300psi gauge for the hpr and backed out the allens on both reg flush to start off.
Went in my backyard to test fire and chrono. Gassed it up and brought the hpr to 250 and the lp to 75. shot over the chron at about 200fps. the dwell was at 8 and it's the early black wired solenoid. Kept raising the hpr to till i got to 300 and the lpr till i got to 100. top speed was 260fps.
I kept changing the dwell higher and higher, but it didn't make a difference. I guessed it was maybe the board. I got one from a friend , a 2.0 that is known to be good and the same results. I had a chance to buy a frenzy board and i was going to replace it anyways, but still no higher velocity.
The battery was good, but i changed that too.
I tore apart and lubed the LPR and HPR and thier pin valves still nothing.
I called Blast and the tech there didn't know what was wrong and said they were backed up and if i sent the gun in it would be 4 weeks before i got it back.
So i tear into it again, took off all the hoses going to the solenoid and make sure there not leaking and all the barbs to be sure they were not blocked. I had 2 spare hi flo barbs and put them on the output of the solenoid and test it again . Now i can get it up to 270fps once in awhile, but a consistent 265fps. I brought the dwell from 8 to 10 to 12 to14 and maxed out to 16 and still the same velocity.
What else is there?
Whatever light you can shine onto this problem would be gladly appreciated
Nomad627